View DS110DF111-14_9077265.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ds110df111 www.ti.com snls461 ? may 2013 low power multi-rate two channel retimer check for samples: ds110df111 1 features description the ds110df111 is a dual channel (1-lane ? pin compatible retimer family bidirectional) retimer with integrated signal ? ds125df111 with dfe : 9.8 to 12.5g conditioning. the ds110df111 includes an input ? ds110df111 with dfe : 8.5 to 11.3g continuous-time linear equalizer (ctle), clock and data recovery (cdr) and transmit driver on each ? adaptive ctle up to 34 db boost at 11.3g channel. ? self tuning 5-tap dfe the ds110df111 with its on-chip decision feedback ? raw equalized and retimed data loopback equalizer (dfe) can enhance the reach and ? adjustable transmit v od : 600 to 1300 mvp-p robustness of long, lossy, cross-talk-impaired high ? settable tx de-emphasis driver 0 to -12db speed serial links to achieve ber < 1x10 -15 . for less demanding applications/interconnects, the dfe can ? low power consumption: 200mw/channel be switched off and achieve the same ber ? locks to half/quarter/eighth data rates for performance. the ds125 and ds110 devices are pin- legacy support compatible. ? on-chip eye monitor (eom), prbs generator each channel of the ds110df111 independently ? input signal detection, cdr lock locks to serial data at data rates from 8.5 to 11.3 detection/indicator gbps or to any supported sub-rate of these data rates. this simplifies system design and lowers ? single 3.3v or 2.5v 5% power supply overall cost. ? smbus, eeprom, or pin based configuration programmable transmit de-emphasis driver offers ? 4 mm x 4 mm, 24-pin qfn package precise settings to meet the sff-8431 template. the ? operating temp range: -40 c to 85 c fully adaptive receive equalization (ctle and dfe) enables longer distance transmission in lossy copper interconnect and backplanes with multiple connectors. the cdr function is ideal for use in front port parallel optical module applications to reset the jitter budget and retime high speed serial data. 1 please be aware that an important notice concerning availability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. production data information is current as of publication date. copyright ? 2013, texas instruments incorporated products conform to specifications per the terms of the texas instruments standard warranty. production processing does not necessarily include testing of all parameters. line card switch fabric asic fpga back plane retimer with dfe retimer with dfe connector qsfp sfp asic fpga qsfp sfp retimer with dfe passive copper cable optical retimer with dfe 10g 10g retimer with dfe retimer with dfe
ds110df111 snls461 ? may 2013 www.ti.com production connection diagram pin out diagram (top view) 2 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111 ina+ina- outb+ addr0/lock vin 18 inb+ inb- 17 14 13 16 los/int# lpf_cp_b lpf_ref_b refclk_in outa+ outa- outb- 15 vdd 2423 2221 2019 11 12 8 10 9 7 lpf_cp_a ensmb 1 2 5 6 3 scl/demb lpf_ref_a sda/dema 4 vdd tx_dis/lbk voda/readen# addr1/vodb/done# top view ds110df111 dap = gnd 4 mm x 4 mm, 0.5 mm pitch
ds110df111 www.ti.com snls461 ? may 2013 pin descriptions pin name pin # i/o type description high speed differential i/os outa+/- 7, 8 o, cml inverting and non-inverting cml-compatible differential outputs. outputs require ac coupling outb+/- 20, 19 o, cml inverting and non-inverting cml-compatible differential outputs. outputs require ac coupling ina+/- 24, 23 i, cml inverting and non-inverting cml-compatible differential inputs. an on- chip 100 ohm terminating resistor connects ina+ to ina- inputs require ac coupling. ti recommends 100 nf capacitors. note that for sfp+ applications, ac coupling is included as part of the sfp+ module. inb+/- 11, 12 i, cml inverting and non-inverting cml-compatible differential inputs. an on- chip 100 ohm terminating resistor connects inb+ to inb- inputs require ac coupling. ti recommends 100 nf capacitors. note that for sfp+ applications, ac coupling is included as part of the sfp+ module. loop filter connection pin lpf_cp_a, lpf_ref_a 2, 1 i/o, analog loop filter connection, place a 22 nf capacitor in series between lpf_cp_a and lpf_ref_a lpf_cp_b, lpf_ref_b 17, 18 i/o, analog loop filter connection, place a 22 nf capacitor in series between lpf_cp_b and lpf_ref_b reference clock i/o refclk_in 14 i, lvcmos 25 mhz 100 ppm clock from external osc indicator pins lock 16 o, lvcmos goes high when cdr lock is attained on the corresponding channel. note that this pin is shared with strap input functions read at startup los/int# 13 o, od output is driven low when a valid signal is present on ch a. output is released when signal on ch a is lost (los). this output can be redefined as an int# signal which will be driven low if the eom check returns a value below the heo/veo interrupt threshold (1) smbus mode pins ensmb 3 i, 4-level system management bus (smbus) enable pin high = register access, smbus slave mode float = smbus master read from external eeprom low = external pin control mode sda 4 i, 4-level data input / open drain output o, od external pull-up resistor is required. pin is 3.3 v lvcmos tolerant (2) scl 5 i, 4-level clock input in smbus slave mode. can also be an open drain output in o, od smbus master mode pin is 3.3 v lvcmos tolerant (2) tx_dis 6 i, 4-level disable the transmitter and put the device in low power mode high = outa enabled/outb disabled low = outa/outb enabled (normal operation) addr0 16 i, lvcmos this pin sets the smbus address for the retimer. this pin is a strap input. the state is read on power-up to set the smbus address in smbus control mode (2) addr1/done# 10 io, lvcmos this pin sets the smbus address for the retimer in smbus slave mode. goes low to indicate that the smbus master eeprom read has been completed in smbus master mode (2) readen# 9 i, 4-level initiates smbus master eeprom read. when multiple ds110ds111 are connected to a single eeprom, the readen# input can be daisychained to the done# output. pull low for proper register operation (2) (1) the los/int# pin is an open drain output which requires external pull-up resistor to 3.3v to achieve a high level. (2) this pin is shared with other functions. copyright ? 2013, texas instruments incorporated submit documentation feedback 3 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com pin descriptions (continued) pin name pin # i/o type description pin control (ensmb = low) (3) dema 4 i, 4-level set cha output de-emphasis level in pin control mode (4) demb 5 i, 4-level set chb output de-emphasis level in pin control mode (4) lbk 6 i, 4-level high = ina goes to outa, inb goes to outb low = ina goes to outb, inb goes to outa (4) voda 9 i, 4-level set cha output launch amplitude in pin control mode (4) vodb 10 i, 4-level set chb output launch amplitude in pin control mode (4) power vdd 21, 22 power vdd = 2.5 v +/- 5% 3.3v mode operation: vdd supply output = 2.5v +/- 5% 2.5v mode operation: vdd supply input = 2.5v +/- 5% vin 15 power regulator input with integrated supply mode control 3.3v mode operation: vin supply input = 3.3v +/- 10% 2.5v mode operation: vin supply input = 2.5v +/- 5% dap pad power ground reference the exposed pad at the center of the package must be connected to ground plane of the board with at least 4 vias to lower the ground impedance and improve the thermal performance of the package (3) when in pin control mode, the production silicon ds110df111 device operates at 1.25 and 10.3125 gbps and has limited vod and de- emphasis control. (4) this pin is shared with other functions. these devices have limited built-in esd protection. the leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the mos gates. absolute maximum ratings min max units supply voltage (v dd ) -0.5 +2.75 v supply voltage (v in ) -0.5 +3.6 v lvcmos input/output voltage -0.5 2.75 v 4-level input voltage (2.5v mode) -0.5 v dd + 0.5 v 4-level input voltage (3.3v mode) -0.5 3.6 v smbus input/output voltage -0.5 3.6 v cml input voltage -0.5 v dd + 0.5 v cml input current -30 +30 ma storage temperature -40 +125 c hbm, std - jesd22-a114f > 2.5 kv cdm, std - jesd22-c101-d > 1.0 kv esd rating package thermal ja , no airflow, 4 layer 42.0 c/w resistance for soldering specifications, see product folder at www.ti.com recommended operating conditions min typ max unit 2.5v mode 2.375 2.5 2.625 supply voltage v 3.3v mode 3.0 3.3 3.6 ambient temperature -40 25 +85 c smbus (sda, scl) 3.0 3.3 3.6 v 4 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 electrical characteristics parameter conditions min typ max unit r_baud input baud rate full rate: ds110df111 8.5 11.3 gbps f sdc smbus clock rate 100 400 khz refclk clock rate +/- 100 ppm 25.0 mhz power supply current 11.3 gbps : ds110df111 170 ma 11.3 gbps : ds110df111 150 ma dfe disabled current consumption i dd maximum transient supply current (whole device) default settings: cha and chb 235 300 ma valid input signal detected cha and chb acquiring lock 50 hz to 100 hz 100 mvp-p ntps supply noise tolerance 100 hz to 10 mhz 40 mvp-p 10 mhz to 5.0 ghz 10 mvp-p lvcmos (lbk, readen#, done#, lock) v ih high level input voltage 2.5v or 3.3v supply modes 1.7 v v il low level input voltage 2.5v or 3.3v supply modes 0.7 v oh high level output voltage i oh = -3 ma 2.0 v v ol low level output voltage i ol = 3 ma 0.4 i in input leakage current v input = gnd or v in -15 +15 ua 4-level inputs (ensmb, dema, demb, tx_dis, voda, vodb) i in-r input leakage current v input = gnd or v in -160 +80 ua open drain (los/int#) v ol low level output voltage i ol = 3 ma 0.4 v signal detect signal detect: default level to assert sdh 20 mvp-p on threshold level signal detect, 10.3125 gbps signal detect: default level to de-assert sdl 15 mvp-p off threshold level signal detect, 10.3125 gbps cml rx inputs r_rd dc input differential resistance 100 ? sdd11 10 mhz -19 rl rx-in input return-loss sdd11 2.0 ghz -14 db sdd11 6.0 - 11.1 ghz -8 v rx- source transmit signal level 600 1600 mvp-p launch cml tx outputs t_v diff0 output differential voltage default setting, prbs31 400 550 675 mvp-p maximum setting, prbs31 t_v diff7 output differential voltage 1000 1250 mvp-p requires smbus control maximum setting, vod and de v od_de de-emphasis level requires smbus control -12 db input: 10.3125gbps, 64t pattern t_rd dc output differential resistance 100 ? full slew rate t r /t f output rise/fall time 20% - 80% 36 psec input: 10.3125 gbps, 8t pattern limited slew rate (reg 0x18) t rs /t fs output rise/fall time 20% - 80% 50 psec input: 10.3125 gbps, 8t pattern copyright ? 2013, texas instruments incorporated submit documentation feedback 5 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com electrical characteristics (continued) parameter conditions min typ max unit sdd22 10 mhz - 2 ghz -19 t sdd22 output differential mode return loss sdd22 5.5ghz -15 db sdd22 11.1ghz -11 t pd propagation delay retimed data 10.3125 gbps 350 psec t pd-raw propagation delay raw data 200 psec transmit jitter specs (1) t tj total jitter (1e-12) prbs7, 10.3125 gbps 7.5 ps t rj random jitter prbs7, 10.3125 gbps 0.33 ps (rms) t dj deterministic jitter prbs7, 10.3125 gbps 3.6 ps (1) rj and dj jitter decomposition as reported by tek dsa8200 sampling scope using a 80e09 electrical sampling module, 80a06 pattern trigger, and 82a04 phase reference module. 6 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 electrical characteristics (continued) parameter conditions min typ max unit clock and data recovery bw pll pll bandwidth -3 db measured at 10.3125 gbps 5 mhz jitter per sff-8431 appendix d.11 j tol total jitter tolerance > 0.70 ui combination of dj, pj, and rj t lock1 cdr lock time standards based (2) 10 - 30 ms lock temperature range temp lock cdr lock 125 0 c -40c to 85c operating range serial bus interface characteristics (3) data, clock input low voltage v il 0.8 v (sda / scl) data, clock input high voltage v ih 2.1 3.6 v (sda / scl) v hy input hystersis > 50 mv v ol output low voltage sda or scl, iol = 1.25 ma 0 0.36 v sda or scl, v input = v in , v dd , i in input current -15 +15 ua gnd t r sda rise time, read operation sda, rpu = 10k, cb < 400 pf 430 ns t f sda fall time, read operation sda, rpu = 10k, cb < 400 pf 20 ns t su;dat setup time, read operation 560 ns t hd;dat hold time, read operation 615 ns t sp input filter 50 ns c in input capacitance sda or scl < 5 pf recommended timing for the serial bus interface f scl scl clock frequency 400 khz t low scl low period 1.3 us t high scl high period 0.6 us t hd;sta hold time, start operation 0.6 us t su;sta setup time, start operation 0.6 us t hd;dat data hold time 0 0.9 us t su;dat data set up time 100 ns t su;sto set up time, stop condtion 0.6 us bus free time t buf 1.3 us between stop - start t r scl and sda, rise time 300 ns t f scl and sda, rise time 300 ns (2) the typical lock time can vary based on data-rate, input channel, and specific ds110df111 settings. (3) eeprom interface requires 400 khz capable eeprom device. copyright ? 2013, texas instruments incorporated submit documentation feedback 7 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com functional description figure 1. ds110df111 data path block diagram the ds110df111 is a low-power, multi-rate, 2-channel retimer. both channels operate independently. each channel includes a continuous time linear equalizer (ctle) which compensates for the presence of a dispersive transmission channel between the source and the ds110df111's input. each channel includes an independent voltage-controlled oscillator (vco) and phase-locked loop (pll) which produce a clean clock. the clean clock produced by the vco and the pll is phase-locked to the incoming data clock, but the high- frequency jitter on the incoming data is attenuated by the pll, producing a clean clock with substantially reduced jitter. this clean clock is used to retime the incoming data, removing high-frequency jitter from the data stream and producing a data output signal with reduced jitter. this provides the clock and data recovery (cdr) function of the retimer. each channel of the ds110df111 features an output driver with settable differential output voltage and settable output de-emphasis. the output de-emphasis compensates for dispersion in the transmission channel at the output of the ds110df111. device data path operation the data path operation of the ds110df111 comprises three functional sections as shown in the data path block diagram of figure 1 . the three functional sections are as follows. ? channel equalization ? clock and data recovery ? output driver channel equalization physical transmission media comprising traces on printed circuit boards (pcbs) or copper cables exhibit a low- pass frequency response characteristic. the magnitude of the high frequency loss varies with the length of the transmission medium and with the loss of the materials which comprise it. this differential high frequency loss and the frequency-dependent group delay of the transmission medium introduce inter-symbol interference in the high-speed broadband signals propagating through the transmission medium. to make configuration of these settings easier, the ds110df111 is designed to determine the correct settings for the ctle autonomously by automatically adapting these equalizations to the input transmission medium. the automatic adaptation takes place when a signal is first detected at the input to the ds110df111, immediately after the ds110df111 acquires phase lock. the automatic adaptation is also triggered whenever the cdr circuitry is reset. the ds110df111 uses its internal eye monitor to generate a figure of merit for the adaptation. the ds110df111 adjusts its ctle boost settings in a systematic way to optimize this figure of merit. 8 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111 in+ in- eq retimer outbuf out+ out- smbus smbus sda scl 1 of 2 channels - ds110rt111 cdr smbus lock ensmb 100 100 signal detect los refclk_in
ds110df111 www.ti.com snls461 ? may 2013 the dfe discriminates against input noise and random jitter as well as against crosstalk at the input to the ds110df111. the dfe tap weights and polarities are adaptive and operate in conjunction with the ctle to achieve an acceptable ber with more severe channel impairments. clock and data recovery the ds110df111 performs its clock and data recovery function by detecting the bit transitions in the incoming data stream and locking its internal vco to the clock represented by the mean arrival times of these bit transitions. this process produces a recovered clock with greatly reduced jitter at jitter frequencies outside the bandwidth of the cdr phase-locked loop (pll). this is the primary benefit of using the ds110df111 in a system. it significantly reduces the jitter present in the data stream, in effect resetting the jitter budget for the system. output driver once the input data has been retimed by the ds110df111 to the recovered, cleaned, clock, it is output to the next device in the signal path using the output driver. the ds110df111 is commonly used in applications where lossy transmission media exist both at the input and the output of the ds110df111. the ctle compensates for lossy transmission media at the input to the ds110df111. the output de-emphasis compensates for the lossy transmission medium at the output of the ds110df111. when there is a transition in the output data stream, the output differential voltage reaches its configured maximum value within the configured rise/fall time of the output driver. following this, the differential voltage rapidly falls off until it reaches the configured vod level minus the configured de-emphasis level. this accentuates the high-frequency components of the output driver signal at the expense of the low frequency components. the pre-distorted ds110df111 output signal, with high-frequency components emphasized relative to its low frequency components, exhibits less inter-symbol interference after traveling down a dispersive transmission medium than an undistorted output signal. an idealized transmit waveform with analog de-emphasis applied figure 2. idealized de-emphasis waveform the output driver is capable of driving variable output voltages with variable amounts of analog de-emphasis. the output voltage and de-emphasis level can be configured by writing registers over the smbus. the ds110df111 cannot determine independently the appropriate output voltage or de-emphasis setting, so the user is responsible for configuring these parameters. they can be set for each channel independently. copyright ? 2013, texas instruments incorporated submit documentation feedback 9 product folder links: ds110df111 1 0.5 0 -0.5 -1 0 1 2 3 4 5 6 7 8 9 10
ds110df111 snls461 ? may 2013 www.ti.com reference clock a 25 mhz +/- 100 ppm reference clock is required for proper device operation. the ds110df111 uses the reference clock to determine when its vco is properly phase-locked to the incoming data-rate. the ds110df111 does not include a crystal driver, so a stand-alone external oscillator is required. the ds110df111 is set to phase lock to a constrained set of data-rates, the digital circuitry in the device pre- configures the vco frequency. this enables the ds110df111 to detect very quickly that a loss of lock has occurred. the phase noise of the reference clock is not critical. any commercially-available 25 mhz oscillator (+/- 100ppm maximum) can provide an acceptable reference clock. the 25 mhz clock high level input voltage must match the vin level utilized on the ds110df111. control pins the 4-level input pins utilize a resistor divider to help set the 4 valid levels and provide a wider range of control settings when ensmb=0. there is an internal 30k pull-up and a 60k pull-down connected to the package pin. these resistors, together with the external resistor connection combine to achieve the desired voltage level. using the 1k pull-up, 1k pull-down, no connect, and 20k pull-down provide the optimal voltage levels for each of the four input states. table 1. 4-level inputs level setting voltage 0 1k to gnd 0.1 v r 20k to gnd 0.33 * vin float no connection 0.67 * vin 1 1k to vin vin - 0.05v in order to minimize the startup current associated with the integrated 2.5v regulator the 1k pull-up / pull-down resistors are recommended. if several 4 level inputs require the same setting, it is possible to combine two or more 1k resistors into a single lower value resistor. as an example; combining two inputs with a single 500 ohm resistor is a good way to save board space. 10 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 smbus interface ensmb pin description to select different programming device, the ensmb pin selects the control modes. the ds110df111device can be programmed using external pin control, a smbus controller, or through an eeprom configuration load. table 2. ensmb control description ensmb pin description readen# pin pull low to initiate reading configuration data from high smbus slave mode the eeprom tie low to enable proper address strapping on float smbus master mode power up r n/a low pin mode control shared with voda pin control function smbus register mode control sda and scl to select different programming device, the ensmb pin selects the control modes. the ds110df111device can be programmed using external pin control, a smbus controller, or through an eeprom configuration load. smbus master mode and smbus slave mode in smbus master mode the ds110df111 reads its initial configuration from an external eeprom upon powerup. once the ds100df410 has finished reading its initial configuration from the external eeprom in smbus master mode it reverts to smbus slave mode and can be further configured by an external controller over the smbus. two device pins initiate reading the configuration from the external eeprom and indicate when the configuration read is complete. ? done# ? readen# these pins are meant to work together. when the ds110df111 is powered up in smbus master mode, it reads its configuration from the external eeprom. this is triggered when the readen# pin goes low. when the ds110df111 is finished reading its configuration from the external eeprom, it drives its done# pin low. in this mode, as the name suggests, the ds110df111 acts as an smbus master during the time it is reading its configuration from the external eeprom. after the ds110df111 has finished reading its configuration from the eeprom, it releases control of the smbus and becomes a smbus slave. in applications where there is more than one ds110df111 on the same smbus, bus contention can result if more than one ds110df111 tries to take command of the smbus as the smbus master at the same time. the readen# and done# pins prevent this bus contention. in a system where the ds110df111s are meant to operate in smbus master mode, the readen# pin of one retimer should be wired to the done# pin of the next. the system should be designed so that the readen# pin of one (and only one) of the ds110df111s in the system is driven low on power-up. this ds110df111 will take command of the smbus on power-up and will read its initial configuration from the external eeprom. when it is finished reading its configuration, it will set its done# pin low. this pin should be connected to the readen# pin of another ds110df111. when this ds110df111 senses its readen# pin driven low, it will take command of the smbus and read its initial configuration from the external eeprom, after which it will set its done# pin low. by connecting the done# pin of each ds110df111 to the readen# pin of the next ds110df111, each ds110df111 can read its initial configuration from the eeprom without causing bus contention. for smbus slave mode, the readen# pin must be tied low. do not leave it floating or tie it high. copyright ? 2013, texas instruments incorporated submit documentation feedback 11 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com address lines in either smbus mode the ds110df111 must be assigned a smbus address. a unique address should be assigned to each device on the smbus. the smbus address is latched into the ds110df111 on power-up. the address is read in from the state of the adr[1:0] lines upon power-up. a floating address line input will be interpreted as a logic 0. the ds110df111 can be configured with any of 4 smbus addresses. the smbus addressing scheme uses the least significant bit of the smbus address as the write/read_n address bit. when an smbus device is addressed for writing, this bit is set to 0; for reading, to 1. table 3 shows the write address setting for the ds110df111versus the values latched in on the address line at power-up. device configuration in smbus slave mode the configurable settings of the ds110df111 may be set independently for each channel at any time after power up using the smbus. a register write is accomplished when the controller sends a start condition on the smbus followed by the write address of the ds110df111 to be configured. see table 3 for the mapping of the address lines to the smbus write addresses. after sending the write address of the ds110df111, the controller sends the register address byte followed by the register data byte. the ds110df111 acknowledges each byte written to the controller according to the data link protocol of the smbus version 2.0 specification. see this specification for additional information on the operation of the smbus. there are two types of device registers in the ds110df111. these are the control/shared registers and the channel registers. the control/shared registers control or allow observation of settings which affect the operation of all channels of the ds110df111. they are also used to select which channel of the device is to be the target channel for reads from and writes to the channel registers. the channel registers are used to set all the configuration settings of the ds110df111. they provide independent control for each channel of the ds110df111 for all the settable device characteristics. any registers not described in the tables that follow should be treated as reserved. the user should not try to write new values to these registers. the user-accessible registers described in the tables that follow provide a complete capability for customizing the operation of the ds110df111 on a channel-by-channel basis. bit fields in the register set many of the registers in the ds110df111 are divided into bit fields. this allows a single register to serve multiple purposes, which may be unrelated. often configuring the ds110df111 requires writing a bit field that makes up only part of a register value while leaving the remainder of the register value unchanged. writing to and reading from the control/shared registers any write operation targeting register 0xff writes to the control/shared register 0xff. this is the only register in the ds110df111 with an address of 0xff. bit 2 of register 0xff is used to select either the control/shared register set or a channel register set. if bit 2 of register 0xff is cleared (written with a 0), then all subsequent read and write operations over the smbus are directed to the control/shared register set. this situation persists until bit 2 of register 0xff is set (written with a 1). there is a register with address 0x00 in the control/shared register set, and there is also a register with address 0x00 in each channel register set. if you read the value in register 0x00 when bit 2 of register 0xff is cleared to 0, then the value returned by the ds110df111 is the value in register 0x00 of the control/shared register set. if you read the value in register 0x00 when bit 2 of register 0xff is set to 1, then the value returned by the ds110df111 is the value in register 0x00 of the selected channel register set. the channel register set is selected by bits 1:0 of register 0xff. if bit 3 of register 0xff is set to 1 and bit 2 of register 0xff is also set to 1, then any write operation to any register address will write all the channel register sets in the ds110df111 simultaneously. this situation will persist until either bit 3 of register 0xff or bit 2 of register 0xff is cleared. note that when you write to register 0xff, independent of the current settings in register 0xff, the write operation always targets the control/shared register 0xff. this channel select register, register 0xff, is unique in this regard. table 4 shows the control/shared register set. 12 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 table 3. smbus write address assignment (1) addr1 addr0 smbus write address smbus read address 0 0 0x30 0x31 0 1 0x32 0x33 1 0 0x34 0x35 1 1 0x36 0x37 (1) a floating addr[1:0] pin at power-up will be interpreted as a logic 0. table 4. control and shared register space default default bit address register bits value mode description (hex) value (hex) (binary) 0x00 00 7:4 0000 r smbus address strap observation < 3:0 > 0x01 7:5 011 r device revision 40 4:0 0 0000 r device id 0x04 6 0 r/w/sc self-clearing reset for control/shared registers 01 5 0 r/w reset for smbus master mode 4 0 r/w force eeprom configuration 0x05 4 0 r indicates eeprom read complete 00 3 0 r indicates channel a has interrupted 2 0 r indicates channel b has interrupted 0x06 write to 0xa ? h to observe smbus address strap in reg 00 3:0 0000 r/w 0x00[7:4] 0x07 loopback: 1 0 r/w loopback input of channel a to output of channel b 04 loopback: 0 0 r/w loopback input of channel b to output of channel a 0xff controls lock pin output 00: logical and of lock status from ch a and ch b 7:6 00 r/w 01: lock status from channel a 10: lock status from channel b 11: logical or of lock status from ch a and ch b loss of signal / interrupt (los/int) pin output 5 0 r/w 0: los 1: interrupt 00 selects both channels for register write. register read from 3 0 r/w one channel based on the selected channel in register 0xff bits 1:0. see table 5 0 = reads/writes directed to shared registers 2 0 r/w 1 = reads/writes directed to channel registers based on target channel defined by register 0xff bits 1:0. see table 5 selects target channel for register reads and writes. see 1:0 0 r/w table 5 smbus strap observation register 0x00, bits 7:4 in order to communicate with the ds110df111 over the smbus, it is necessary for the smbus controller to know the address of the ds110df111. the address strap observation bits in control/shared register 0x00 are primarily useful as a test of smbus operation. in order to use the address strap observation bits of control/shared register 0x00, it is necessary first to set the diagnostic test control bits of control/shared register 0x06. this four bit field should be written with a value of 0xa. when this value is written to bits 3:0 of control/shared register 0x06, then the value of the smbus address straps can be read in register 0x00, bits 7:4. the value read will be the same as the value present on the addr line when the ds110df111 powers up. for example, if a value of 0x0 is read from control/shared register 0x00, bits 7:4, then at power-up the addr line was set to 0. the ds110df111 is set to a smbus write address of 0x30. copyright ? 2013, texas instruments incorporated submit documentation feedback 13 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com interrupt channel flag bits register 0x05, bits 3:2 the operation of these bits is described in the section on interrupt handling later in this data sheet. control/shared register reset register 0x04, bit 6 register 0x04, bit 6, clears all the control/shared registers back to their factory defaults. this bit is self clearing, so it is cleared after it is written and the control/shared registers are reset to their factory default values. device revision and device id register 0x01 control/shared register 0x01 contains the device revision and device id. the device id will be different for the different devices in the retimer family. this register is useful because it can be interrogated by software to determine the device variant and revision installed in a particular system. the software might then configure the device with appropriate settings depending upon the device variant and revision. table 5. channel select register values mapped to register set target broadcast targeted shared/channel register 0xff channel channel register comments value (hex) register register selection selection selection 0x00 shared n/a n/a all reads and writes target shared register set 0x01 shared n/a n/a all reads and writes target shared register set 0x02 shared n/a n/a all reads and writes target shared register set 0x03 shared n/a n/a all reads and writes target shared register set 0x04 channel no a all reads and writes target channel register set 0x05 channel no b all reads and writes target channel register set 0x08 shared n/a n/a all reads and writes target channel register set 0x09 shared n/a n/a all reads and writes target shared register set 0x0a shared n/a n/a all reads and writes target shared register set 0x0b shared n/a n/a all reads and writes target shared register set all writes target all channel register sets, all reads 0x0c channel yes a target channel a register set all writes target all channel register sets, all reads 0x0d channel yes b target channel b register set channel select register register 0xff, bits 3:0 register 0xff, as described above, selects the channel or channels for channel register reads and writes. it is worth describing the operation of this register again for clarity. if bit 3 of register 0xff is set, then any channel register write applies to all channels. channel register read operations always target only the channel specified in bits 1:0 of register 0xff regardless of the state of bit 3 of register 0xff. read and write operations target the channel register sets only when bit 2 of register 0xff is set. bit 2 of register 0xff is the universal channel register enable. this bit must be set in order for any channel register reads and writes to occur. if this bit is set, then read operations from or write operations to register 0x00, for example, target channel register 0x00 for the selected channel rather than the control/shared register 0x00. in order to access the control/shared registers again, bit 2 of register 0xff should be cleared. then the control/shared registers can again be accessed using the smbus. write operations to register 0xff always target the register with address 0xff in the control/shared register set. there is no other register, and specifically, no channel register, with address 0xff. 14 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 the contents of the channel select register, register 0xff, cannot be read back over the smbus. read operations on this register will always yield an invalid result. all eight bits of this register should always be set to the desired values whenever this register is written. always write 0x0 to the four most significant bits of register 0xff. the register set target selected by each valid value written to the channel select register is shown in table 5 . reading to and writing from the channel registers each channel has a complete set of channel registers associated with it. the channel registers or the control/ shared registers are selected by channel select register 0xff. the settings in this register control the target for subsequent register reads and writes until the contents of register 0xff are explicitly changed by a register write to register 0xff. as noted, there is only one register with an address of 0xff, the channel select register. table 6. channel register definition default address default bit register bits mode description (hex) value (binary) value (hex) reset channel registers to defaults 0x00 00 2 0 r/w/sc (self-clearing) 4 0 r cdr lock loss interrupt 0x01 00 0 0 r signal detect loss interrupt cdr status [7:0] bit[7] = ppm count met bit[6] = auto adapt complete bit[5] = fail lock check 0x02 00 7:0 00 ? h r bit[4] = lock bit[3] = cdr lock bit[2] = single bit limit reached bit[1] = comp lpf high bit[0] = comp lpf low 7:6 00 r/w used for setting ctle value when channel register 0x2d[3] is high. read-back value going 5:4 00 r/w to analog in channel register 0x52. 3:2 00 r/w 0x03 00 ctle boost stage [0] < 1:0 > bits [7:6] ctle boost stage [1] < 1:0 > bits [5:4] ctle boost stage [2] < 1:0 > bits [3:2] 1:0 00 r/w ctle boost stage [3] < 1:0 > bits [1:0] enable override output mux 5 0 r/w (register 0x1e[7:5]) 0x09 00 enable override divider select 2 0 r/w (register 0x18[6:4]) 3 0 r/w enable cdr reset override (register 0x0a[2]) 0x0a 10 2 0 r/w cdr reset override bit 7:4 0000 r/w status control[3:0] single bit transition detector ? lock 0x0c 08 qualification 3 1 r/w 1: enables sbt 0: disables sbt prbs pattern shift enable. use in conjunction with 0x1e[4] and 0x30[3] to 0x0d 00 5 0 r/w start prbs. note: this bit must be set high last. copyright ? 2013, texas instruments incorporated submit documentation feedback 15 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 6. channel register definition (continued) default address default bit register bits mode description (hex) value (binary) value (hex) eye opening monitor voltage range < 1:0 > 00: 3.125 mv 7:6 00 r/w 01: 6.250 mv 10: 9.375 mv 11: 12.500 mv 5 1 r/w eye opening monitor power down dfe tap 2 polarity 3 0 r/w 0x11 20 (use w/manual dfe override, 0x15[7]) dfe tap 3 polarity 2 0 r/w (use w/manual dfe override, 0x15[7]) dfe tap 4 polarity 1 0 r/w (use w/manual dfe override, 0x15[7]) dfe tap 5 polarity 0 0 r/w (use w/manual dfe override, 0x15[7]) dfe tap 1 polarity 7 1 r/w (use w/manual dfe override, 0x15[7]) 0x12 a0 5 1 r/w dfe select negative gm 4:0 0000 r/w dfe tap 1 weight < 4:0 > 4 1 r/w enable dc offset control 0x13 90 2 0 r/w ctle boost stage 3, bit 2 (limiting bit) 1 0 r/w enable dwdm mode 7 0 r/w force signal detect on 6 0 r/w force signal detect off 0x14 00 5:4 00 r/w signal detect ? assert reference levels 3:2 00 r/w signal detect ? de-assert reference levels enables manual dfe tap settings 7 0 r/w use with 0x11[3:0], 0x12[7], 0x12[4:0], 0x20[7:0], 0x21[7:0] 6 0 r/w compress the range of de-emphasis to 0-6 db 0x15 10 3 0 r/w driver power-down driver de-emphasis setting < 2:0 > ; 0db - 12db; 2:0 000 r/w see table 16 vco divider ratio < 2:0 > (enable from register 0x09, bit 2) 000: full-rate 6:4 000 r/w 001: divide by 2 0x18 40 010: divide by 4 011: divide by 8 100: default value at power up 2 0 r/w enable slow rise/fall time edge rate selects pfd mux for loopback 000: raw data 7:5 111 r/w 001: re-timed data 100: prbs generator 0x1e e1 111: mute enable the prbs serializer, used with 0x1e[7:5], 4 0 r/w 0x30[3:0], 0x0d[5] 3 0 r/w disable the dfe function (disable = 1) 0x1f 55 7 0 r/w invert the polarity of the driver dfe tap 5 weight < 3:0 > 7:4 0000 r/w (use w/manual dfe override, 0x15[7]) 0x20 00 dfe tap 4 weight < 3:0 > 3:0 0000 r/w (use w/manual dfe override, 0x15[7]) 16 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 table 6. channel register definition (continued) default address default bit register bits mode description (hex) value (binary) value (hex) dfe tap 3 weight < 3:0 > 7:4 0000 r/w (use w/manual dfe override, 0x15[7]) 0x21 00 dfe tap 2 weight < 3:0 > 3:0 0000 r/w (use w/manual dfe override, 0x15[7]) 0x23 40 6 1 r/w dfe override 7 0 r/w enable fast eye opening monitor mode 2 0 r/w/sc start dfe adaptation (self- clearing) 0x24 00 start eye opening monitor counter 0 0 r/w/sc (self-clearing) 0x25 00 7:0 00 ? h r eye opening monitor count < 15:8 > 0x26 00 7:0 00 ? h r eye opening monitor count < 7:0 > heo value < 7:0 > 0x27 00 7:0 00 ? h r (measured in 0-63 phase settings) 0x28 00 7:0 00 ? h r veo value < 7:0 > eye opening monitor voltage range setting 0x29 00 6:5 00 r < 1:0 > see 0x11[7:6] 0x2a 30 7:0 30 ? h r/w eye opening monitor timer threshold < 7:0 > dfe adaptation figure of merit type < 1:0 > 00: not valid 5:4 11 r/w 01: state machine uses only heo 10: state machine uses only veo 0x2c 72 11: state machine uses both heo and veo determines number of dfe settings to look- 3:0 0010 r/w beyond current best figure of merit (fom) 7 1 r/w enable driver short circuit protection 6 0 r/w enable fast signal detect increase the assert and de-assert reference 5 0 r/w thresholds 4 0 r/w set high (1) to decrease the signal detect gain set high (1) to override the eq setting going to 3 0 r/w the analog from 0x03[7:0] 0x2d 80 output driver vod [2:0] 000: 600 mv 001: 700 mv 010: 800 mv 2:0 000 r/w 011: 900 mv 100: 1000 mv 101: 1100 mv 110: 1200 mv 111: 1300 mv 7:6 0 r/w rate < 1:0 > 5:4 0 r/w subrate < 1:0 > ctle adaptation index override 0: ctle adaption will start at reg_0x40 + reg_0x39[3:0]. so this may be used to preclude lower ctle settings. 0x2f 06 1: ctle will not adapt and will use the ctle 3 0 r/w setting of reg_0x40 + reg_0x39[3:0] for scalar divide ratios of 1 or 2. divide ratios of 4 & 8 will take ctle settings from 0x3a unless 0x55[0] is high, which will revert to the setting in reg_0x40 + reg_0x39[3:0]. 0 0 r start ctle adaptation copyright ? 2013, texas instruments incorporated submit documentation feedback 17 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 6. channel register definition (continued) default address default bit register bits mode description (hex) value (binary) value (hex) 4 0 r goes high if interrupt from cdr goes high 0x30 00 3 0 r/w enable prbs digital clk adaptation mode < 1:0 > 00: no adaption 01: adapt only ctle till optimal 6:5 10 r/w 10: adapt ctle till optimal, then dfe, then ctle again 11: adapt ctle till lock, then dfe, then ctle 0x31 40 till optimal ctle adaptation figure of merit type < 1:0 > 00: sm uses both heo and veo 4:3 00 r/w 01: sm uses only heo 10: sm uses only veo 11: sm uses both heo and veo heo interrupt threshold < 3:0 > 7:4 0001 r/w compares heo value, reg_0x27[7:0] vs. threshold of reg_0x32[7:4]*4 0x32 11 veo interrupt threshold < 3:0 > 3:0 0001 r/w compares veo value, reg_0x28[7:0] vs. threshold of reg_0x32[3:0]*4 heo threshold for ctle adaptation handoff to dfe adaptation 7:4 1000 r/w compares heo value, reg_0x27[7:0] vs. threshold of reg_0x33[7:4]*2 0x33 88 veo threshold for ctle adaptation handoff to dfe adaptation 3:0 1000 r/w compares heo value, reg_0x27[7:0] vs. threshold of reg_0x33[3:0]*2 maximum dfe tap absolute value for taps 2 ? 5 0x34 3f 3:0 1111 r/w < 3:0 > maximum dfe tap absolute value for tap 1 0x35 1f 4:0 1 1111 r/w < 4:0 > 6 0 r/w enable heo/veo interrupt 5:4 11 r/w reserved 0x36 33 2 0 r/w reserved 1:0 11 r/w reserved start index for ctle adaptation < 4:0 > 0x39 00 4:0 0 0000 r/w (enable from register 0x2f, bit 3) fixed ctle stage 0 boost setting for divide 7:6 10 r/w ratios 4 and 8 < 1:0 > fixed ctle stage 1 boost setting for divide 5:4 10 r/w ratios 4 and 8 < 1:0 > 0x3a a5 fixed ctle stage 2 boost setting for divide 3:2 01 r/w ratios 4 and 8 < 1:0 > fixed ctle stage 3 boost setting for divide 1:0 01 r/w ratios 4 and 8 < 1:0 > enable heo/veo lock monitoring once sbt/fld declare lock. once the lock and adaptation 0x3e 80 7 1 r/w processes are complete, heo/veo monitoring is performed once per the interval determined by reg_0x69[3:0]. 0x40 - 0x4f ctle settings for adaptation 4 0 r/w slicer sign bit 0x50 00 slicer adjustment in 5mv steps. maximum 3:0 0000 r/w adjustment value is 50mv or 0x50[3:0] = a ? h 0x52 00 7:0 00 ? h r ctle boost setting readback register. 18 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 table 6. channel register definition (continued) default address default bit register bits mode description (hex) value (binary) value (hex) 7 0 r signal detect observation bit. 6 0 r eq limiting (ctle stage 3[2]) observation bit. 0x54 00 1 0 r cdr lock interrupt 0 0 r signal detect interrupt allows observation of the alternate heo/veo 4 0 r figure of merit 0x55 00 in reg_0x27 and reg_0x28 0 0 r enables adaption in the lower divide ratios 1 0 r/w cdr loss of lock. sticky bit. clears when read 0x56 00 0 0 r/w loss of signal. sticky bit. clears when read group 0 (rate/subrate defined) ppm counter 0x60 00 7:0 00 ? h r/w < 7:0 > lsbs override standard group 0 tie cells for ppm 7 0 r/w count and tolerance with channel registers 0x60, 0x61, and 0x64 0x61 00 group 0 (rate/subrate defined) ppm counter 6:0 000 0000 r/w < 14:8 > msbs group 1 (rate/subrate defined) ppm counter 0x62 00 7:0 00 ? h r/w < 7:0 > lsbs override standard group 1 tie cells for ppm 7 0 r/w count and tolerance with channel registers 0x62, 0x63, and 0x64 0x63 00 group 1 (rate/subrate defined) ppm counter 6:0 000 0000 r/w < 14:8 > msbs 7:4 0000 r/w group 0 ppm delta 0x64 00 3:0 0000 r/w group 1 ppm delta heo/veo interval while monitoring lock. monitoring will take place 1 out of the indicated 0x69 0a 3:0 1010 r/w count intervals (default h'a). interval time is determined 0x2b[5:4], which is 6.5ms by default. 7:4 0100 r/w vertical eye opening lock threshold < 3:0 > 0x6a 44 3:0 0100 r/w horizontal eye opening lock threshold < 3:0 > adaptation figure of merit term a < 7:0 > fom = min [(heo - b)*a, (veo - c)*(1-a)] 0x6b 40 7:0 40 ? h r/w fom = min [(heo - 0x6c) * (0x6b)/127, (veo - 0x6d) * (128 - 0x6b)/127] adaptation figure of merit term b < 7:0 > fom = min [(heo - b)*a, (veo - c)*(1-a)] 0x6c 00 7:0 0x0 r/w fom = min [(heo - 0x6c) * (0x6b)/127, (veo - 0x6d) * (128 - 0x6b)/127] adaptation figure of merit term c < 7:0 > fom = min [(heo - b)*a, (veo - c)*(1-a)] 0x6d 00 7:0 0x0 r/w fom = min [(heo - 0x6c) * (0x6b)/127, (veo - 0x6d) * (128 - 0x6b)/127] enable alternate figure of merit for ctle 7 0x0 r/w adaptation 0x6e 00 enable alternate figure of merit for dfe 6 0x0 r/w adaptation 0x70 03 2:0 011 r/w ctle adaptation look-beyond count < 2:0 > 5 0 r dfe tap 1 polarity (read only) 0x71 00 4:0 0 0000 r dfe tap 1 weight (read only) < 4:0 > 4 0 r dfe tap 2 polarity (read only) 0x72 00 3:0 0000 r dfe tap 2 weight (read only) < 3:0 > copyright ? 2013, texas instruments incorporated submit documentation feedback 19 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 6. channel register definition (continued) default address default bit register bits mode description (hex) value (binary) value (hex) 4 0 r dfe tap 3 polarity (read only) 0x73 00 3:0 0000 r dfe tap 3 weight (read only) < 3:0 > 4 0 r dfe tap 4 polarity (read only) 0x74 00 3:0 0000 r dfe tap 4 weight (read only) < 3:0 > 4 0 r dfe tap 5 polarity (read only) 0x75 00 3:0 0000 r dfe tap 5 weight (read only) < 3:0 > resetting individual channels of the retimer register 0x00, bit 2, and register 0x0a, bits 3:2 bit 2 of channel register 0x00 is used to reset all the registers for the corresponding channel to their factory default settings. this bit is self-clearing. writing this bit will clear any register changes you have made in the ds110df111 since it was powered-up. to reset just the cdr state machine without resetting the register values, which will re-initiate the lock and adaptation sequence for a particular channel, use channel register 0x0a. set bit 3 of this register to enable the reset override, then set bit 2 to force the cdr state machine into reset. these bits can be set in the same operation. when bit 2 is subsequently cleared, the cdr state machine will resume normal operation. if a signal is present at the input to the selected channel, the ds110df111 will attempt to lock to it and will adapt its ctle and its dfe according to the currently configured adapt mode for the selected channel. the adapt mode is configured by channel register 0x31, bits 6:5. 20 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 rate and subrate setting each channel of the ds110df111 will, by default operate at 10.3125 gbps and 1.25 gbps. the device can be configured to operate at other vco frequencies between 8.5 ghz and 11.3 ghz using the rate (reg: 0x2f bits [7:6]) and subrate (reg: 0x2f bits [5:4]) registers. the ds110df111 is designed to lock to signals conforming to several different data transmission standards. these standards may define a single data rate or multiple data rates. the rate and subrate settings of the ds110df111 may be used to select a data transmission standard to which the input signal is expected to conform. the ds110df111 searches each data rate applicable to the selected standard to find a valid signal to which it then phase locks. table 7. rate/subrate vco and data-rate information group 0 group 1 input data group 0 group 1 rate subrate divide divide ds110df111 ds125df111 rates vco vco ratios ratios 1.25g, 00 00 8 1 10g 10.3125g x x 10.3125g 2.125g, 00 01 4.25g, 8.5g, 1, 2, 4 1 8.5g 10.51875g x x 10.51875g 2.5g, 5g, 00 10 1, 2, 4 1, 2, 4 10g 10g x x 10g 2.4576g, 00 11 4.9152g, 1, 2, 4 1, 2, 4 9.8304g 9.8304g x x 9.8304g 3.072g, 01 00 2, 4 2, 4 12.288g 12.288g x 6.144g 2.48832g, 01 01 1, 4 1, 4 9.95328g 9.95328g x x 9.95328g 1.5g, 3g, 01 10 1, 2, 4, 8 1, 2, 4, 8 12.0g 12.0g x 6g, 12g 01 11 8.25g 1 1 8.25g 8.25g 10 00 8.5g 1 1 8.5g 8.5g x 10 01 11.5g 1 1 11.5g 11.5g x 10 10 6.25g, 12.5g 2 2 12.5g 12.5g x 3.125g, 10 11 2, 4 2, 4 12.5g 12.5g x 6.25g 11 00 10.3125g 1 1 10.3125g 10.3125g x x 11 01 9.95328g 1 1 9.95328g 9.95328g x x 11 10 7.5g 1 1 7.5g 7.5g 1.25g, 11 11 8 1 10g 10.3125g x x 10.3125g overriding the ctle boost setting register 0x03, register 0x2d, bit 3, and register 0x3a to override the adaptive ctle boost settings, channel register 0x03 is used in conjuction with override register bit for the ctle (0x2d[3]). the current ctle setting applied to the high-speed analog input can always be readback from register 0x52. this readback register value is valid for adaptive ctle settings or when the override mechanism is enabled and the ctle value from register 0x03 is being used. when in divide by 4 or 8 vco settings, ctle channel register 0x3a comes into play. divide by 4 and divide by 8 data-rates do not automatically adapt the ctle setting, they use the value in register 0x3a as a settable ctle level. copyright ? 2013, texas instruments incorporated submit documentation feedback 21 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 8. default output status description input signal channel status output status status not present no signal detected mute present not locked mute present locked raw or retimed, set by 0x1e[7], 0x09[5] table 9. output multiplexer override settings, retimed or raw, register 0x1e bit 7 output bit field value comments multiplexer 0x1 retimed data default when the retimer is locked 0x0 raw data output of the ctle + dfe, before retiming overriding the output multiplexer register 0x09, bit 5, register 0x14, bits 7:6, and register 0x1e, bits 7:5 by default, the ds110df111 output for each channel will be as shown in table 8 and table 9 . this default behavior can be modified by register writes. register 0x1e, bits 7:5, contain the output multiplexer override value. the values of this three-bit field and the corresponding meanings of each are shown in table 9 . when no signal is present at the input to the selected channel of the ds110df111 the signal detect circuitry will power down the channel. this includes the output driver which is therefore muted when no signal is present at the input. table 10. divider ratio map bit field value reg 18 [6:4] divider ratio 0 1 1 2 2 4 3 8 22 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 overriding the vco divider selection register 0x09, bit 2, and register 0x18, bits 6:4 in normal operation, the ds110df111 sets its vco divider to the correct divide ratio, either 1, 2, 4, or 8 depending upon the bit rate of the signal at the channel input. it is possible to override the divider selection. this might be desired if the vco is set to free run, for example, to output a signal at a sub-harmonic of the actual vco frequency. in order to override the vco divider settings, first set bit 2 of register 0x09. this is the vco divider override enable. once this bit is set, the vco divider setting is controlled by the value in register 0x18, bits 6:4. the valid values for this three-bit field are 0x0 to 0x3. the mapping of the bit field values to the divider ratio is shown in table 10 . in normal operation, the ds110df111 will determine the required vco divider ratio automatically. in order for the ds110df111 to acquire lock, the override divider selection must be included in the group 0 vco list for the current rate/subrate setting. using the internal eye opening monitor register 0x11, bits 7:6 and bit 5, register 0x22, bit 7, register 0x24, bit 7 and bit 0, register 0x25, register 0x26, register 0x27, register 0x28, register 0x2a and register 0x3e, bit 7 the ds110df111 includes an internal eye opening monitor. the eye opening monitor is used by the retime to compute a figure of merit for automatic adaptation of the ctle and the dfe. it can also be controlled and queried through the smbus by a system controller. the eye opening monitor produces error hit counts for settable phase and voltage offsets of the comparator in the retimer. this is similar to the way many bit error rate test sets measure eye opening. at each phase and amplitude offset setting, the eye opening monitor determines the nominal bit value ( ? 0 ? or ? 1 ? ) using its primary comparator. this is the bit value that is resynchronized to the recovered clock and presented at the output of the ds110df111. the eye opening monitor also determines the bit value detected by the offset comparator. this information yields an eye contour. here's how this works. if the offset comparator is offset in voltage by an amount larger than the vertical eye opening, for example, then the offset comparator will always decide that the current bit has a bit value of ? 0 ? . when the bit is really a ? 1 ? , as determined by the primary comparator, this is considered a bit error. the number of bit errors is counted for a settable interval at each setting of the offset phase and voltage of the offset comparator. these error counts can be read from registers 0x25 and 0x26 for sequential phase and voltage offsets. these error counts for all phase and voltage offsets form a 64 x 64 point array. a surface or contour plot of the error hit count versus phase and voltage offset produces an eye diagram, which can be plotted by external software. the eye opening monitor works in two modes. in the first, only the horizontal and vertical eye openings are measured. the eye opening monitor first sweeps its variable-phase clock through one unit interval with the comparison voltage set to the mid-point of the signal. this determines the mid-point of the horizontal eye opening. the eye opening monitor then sets its variable phase clock to the mid-point of the horizontal eye opening and sweeps its comparison voltage. these two measurements determine the horizontal and vertical eye openings. the horizontal eye opening value is read from register 0x27 and the vertical eye opening from register 0x28. both values are single byte values. the measurement of horizontal and vertical eye opening is very fast. the speed of this measurement makes it useful for determining the adaptation figure of merit. in normal operation, the heo and veo are automatically measured periodically to determine whether the ds110df111 is still in lock. reading registers 0x27 and 0x28 will yield the most-recently measured heo and veo values. in normal operation, the eye monitor circuitry is powered down most of the time to save power. when the eye is to be measured under external control, it must first be enabled by writing a 0 to bit 5 of register 0x11. the default value of this bit is 1, which powers down the eye monitor except when it is powered-up periodically by the cdr state machine and used to test cdr lock. the eye monitor must be powered up to measure the eye under external smbus control. bits 7:6 of register 0x11 are also used during eye monitor operation to set the eom voltage range. this is described below. a single write to register 0x11 can set both bit 5 and bits 7:6 in one operation. copyright ? 2013, texas instruments incorporated submit documentation feedback 23 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com register 0x3e, bit 7, enables horizontal and vertical eye opening measurements as part of the lock validation sequence. when this bit is set, the cdr state machine periodically uses the eye monitor circuitry to measure the horizontal and vertical eye opening. if the eye openings are too small, according to the pre-determined thresholds in register 0x6a, then the cdr state machine declares lock loss and begins the lock acquisition process again. for smbus acquisition of the internal eye, this lock monitoring function must be disabled. prior to overriding the eom by writing a 1 to bit 0 of register 0x24, disable the lock monitoring function by writing a 0 to bit 7 of register 0x3e. once the eye has been acquired, you can reinstate heo and veo lock monitoring by once again writing a 1 to bit 7 of register 0x3e. under external smbus control, the eye opening monitor can be programmed to sweep through all its 64 states of phase and voltage offset autonomously. this mode is initiated by setting register 0x24, bit 7, the fast_eom mode bit. register 0x11, bits 7:6 and bit 5, register 0x22, bit 7, register 0x24, bit 7 and bit 0, register 0x25, register 0x26, register 0x27, register 0x28, register 0x2a and register 0x3e, bit 7 register 0x22, bit 7, the eom_ov bit, should be cleared in this mode. when the fast_eom bit is set, the eye opening monitor operation is initiated by setting bit 0 of register 0x24, which is self-clearing. as soon as this bit is set, the eye opening monitor begins to acquire eye data. the results of the eye opening monitor error counter are stored in register 0x25 and 0x26. in this mode the eye opening monitor results can be obtained by repeated multi-byte reads from register 0x25. it is not necessary to read from register 0x26 for a multi-byte read. as soon as the eight most significant bits are read from register 0x25, the eight least significant bits for the current setting are loaded into register 0x25 and they can be read immediately. as soon as the read of the eight most significant bits has been initiated, the ds110df111 sets its phase and voltage offsets to the next setting and starts its error counter again. the result of this is that the data from the eye opening monitor is available as quickly as it can be read over the smbus with no further register writes required. the external controller just reads the data from the ds110df111 over the smbus as fast as it can. when all the data has been read, the ds110df111 clears the eom_start bit. if multi-byte reads are not used, meaning that the device is addressed each time a byte is read from it, then it is necessary to read register 0x25 to get the msb (the eight most significant bits) and register 0x26 to get the lsb (the eight least significant bits) of the current eye monitor measurement. again, as soon as the read of the msb has been initiated, the ds110df111 sets its phase and voltage offsets to the next setting and starts its error counter again. in this mode both registers 0x25 and 0x26 must be read in order to get the eye monitor data. the eye monitor data for the next set of phase and voltage offsets will not be loaded into registers 0x25 and 0x26 until both registers have been read for the current set of phase and voltage offsets. in all eye opening monitor modes, the amount of time during which the eye opening monitor accumulates eye opening data can be set by the value of register 0x2a. in general, the greater this value the longer the accumulation time. when this value is set to its maximum possible value of 0xff, the maximum number of samples acquired at each phase and amplitude offset is approximately 218. even with this setting, the eye opening monitor values can be read from the smbus with no delay. the eye opening monitor operation is sufficiently fast that the smbus read operation cannot outrun it. the eye opening is measured at the input to the data comparator. at this point in the data path, a significant amount of gain has been applied to the signal by the ctle. in many cases, the vertical eye opening as measured by the eom will be on the order of 400 to 500 mv peak-to-peak. the secondary comparator, which is used to measure the eye opening, has an adjustable voltage range from 100 mv to 400 mv. the eom voltage range is normally set by the cdr state machine during lock and adaptation, but the range can be overridden by writing a two-bit code to bits 7:6 of register 0x11. the values of this code and the corresponding eom voltage ranges are shown in table 11 . table 11. eom voltage range vs reg 0x11 [7:6] value in bits 7:6 of eom voltage range ( mv) register 0x11 0x0 100 0x1 200 0x2 300 0x3 400 24 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 note that the voltage ranges shown in table 11 are the voltage ranges of the signal at the input to the data path comparator. these values are not directly equivalent to any observable voltage measurements at the input to the ds110df111. note also that if the eom voltage range is set too small the voltage sweep of the secondary comparator may not be sufficient to capture the vertical eye opening. when this happens the eye boundaries will be outside the vertical voltage range of the eye measurement. to summarize, the procedure for reading the eye monitor data from the ds110df111is shown below. 1. select the ds110df111 channel to be used for the eye monitor measurement by writing the channel select register, register 0xff, with the appropriate value as shown in table 5 if the correct channel register set is already selected, this step may be skipped. 2. select the eye monitor voltage range by setting bits 7:6 of register 0x11 according to the values in table 11 . the cdr state machine will have set this range during lock acquisition, but it may be necessary to change it to capture the entire vertical eye extent. 3. power up the eye monitor circuitry by clearing bit 5 of register 0x11. normally the eye monitor circuitry is powered up periodically by the cdr state machine. clearing bit 5 of register 0x11 enables the eye monitor circuitry unconditionally. this bit should be set again once the eye acquisition is complete. clearing bit 5 and setting bits 7:6 of register 0x11 as desired can be combined into a single register write if desired. 4. clear bit 7 of register 0x22. this is the eye monitor override bit. it is cleared by default, so you may not need to change it. 5. set bit 7 of register 0x24. this is the fast eye monitor enable bit. 6. set bit 1 of register 0x24. this initiates the automatic fast eye monitor measurement. this bit can be set at the same time a bit 7 of register 0x24 if desired. 7. read the data array from the ds110df111. this can be accomplished in two ways. ? if you are using multi-byte reads, address the ds110df111 to read from register 0x25. continue to read from this register without addressing the device again until you have read all the data desired. the read operation can be interrupted by addressing the device again and then resumed by reading once again from register 0x25. ? if you are not using multi-byte reads, then read the msb for each phase and amplitude offset setting from register 0x25 and the lsb for each setting from register 0x26. in this mode, you address the device each time you want to read a new byte. 8. in either mode, the first four bytes do not contain valid data. these should be discarded. 9. continue reading eye monitor data until you have read the entire 64x64 array. 10. clear bit 7 of register 0x24. this disables fast eye monitor mode. 11. set bit 5 of register 0x11. this will return control of the eye monitor circuitry to the cdr state machine. 12. set bit 7 of register 0x3e. this re-enables the heo and veo lock monitoring. copyright ? 2013, texas instruments incorporated submit documentation feedback 25 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com overriding the dfe tap weights and polarities register 0x11, bits 3:0, register 0x12, bit 7 and bits 4:0, register 0x15, bit 7, register 0x1e, bit 3, register 0x20, register 0x21, register 0x23, bit 6, register 0x24, bit 2, register 0x2f, bit 0, and registers 0x71 ? 0x75 for the ds110df111 the dfe tap weights and polarities are normally set automatically by the adaptation procedure. these values can be overridden by the user if desired. prior to overriding the dfe tap weights and polarities, the dfe_ov bit, bit 6 of register 0x23, should be set. this bit is set by default. in order for the dfe tap weights and polarities to be applied to the input signal, bit 3 of register 0x1e, the dfe_pd bit, which powers down the dfe, should be cleared. this bit is cleared by default. it is not necessary to change the default settings of these registers, but verify that they are set as described. it is necessary to set bit 7 of register 0x15 to manually set the dfe tap weights. this bit is cleared by default. bits 4:0 of register 0x12 set the five-bit weight for dfe tap 1. the first dfe tap has a five-bit setting, while the other taps are set using four bits. often the first dfe tap has the largest effect in improving the bit error rate of the system, which is why this tap has a five-bit weight setting. the polarity of the tap weight for tap 1 is set using bit 7 of the same register, register 0x12. the polarity is set to 0 by default, which corresponds to a negative algebraic sign for the tap. the other four taps are set using four-bit fields in registers 0x20 and 0x21. the polarities of these taps are set by bits 3:0 in register 0x11. these tap polarities are all set to 0 by default. as is the case for the ctle settings, if changing the dfe tap weights or polarities causes the ds110df111 to lose lock, it may readapt its ctle in order to reacquire lock. if this occurs, the ctle settings may appear to change spontaneously when the dfe tap weights are changed. the mechanism is the same as that described above for the ctle boost settings. when the ds110df111 is set to adapt mode 2 or 3 using bits 6:5 of register 0x31, it will automatically adapt its dfe whenever its cdr state machine is reset. this occurs when the user manually resets the cdr state machine using bits 3:2 of register 0x0a, or when a signal is first presented at the input to the channel when the channel is in an unlocked state. regardless of the adapt mode, dfe adaptation can be initiated under smbus control. because the dfe tap weight registers are used by the dfe state machine during adaptation, they may be reset prior to adaptation, which can cause the adaptation to fail. the dfe tap observation registers can be used to prevent this. prior to initiating dfe adaptation under smbus control, write the starting values of the dfe tap settings into the dfe tap weight registers, registers 0x11, 0x12, 0x20, and 0x21. the values can be read from the observation registers, registers 0x71 through 0x75. for each dfe tap, read the current value in the observation register. both the polarities and the tap weights are contained in the observation registers. for each dfe tap, write the current tap polarity and tap weight into the dfe tap register. once all these values have been written, dfe adaptation can be initiated and it will proceed normally. if the ds110df111 fails to find a set of dfe tap weights producing a better adaptation figure of merit than the starting tap weights, the starting tap weights will be retained and used. ctle adaptation can also be initiated manually. setting and then clearing bit 0 of register 0x2f will initiate adaptation of the ctle. as with the dfe, if the ds110df111 fails to find a set of ctle settings that produce a better adaptation figure of merit than the starting ctle values, the starting ctle values will be retained and used. 26 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 enabling slow rise/fall time on the output driver register 0x18, bit 2 normally the rise and fall times of the output driver of the ds110df111 are set by the slew rate of the output transistors. by default, the output transistors are biased to provide the maximum possible slew rate, and hence the minimum possible rise and fall times. in some applications, slower rise and fall times may be desired. for example, slower rise and fall times may reduce the amplitude of electromagnetic interference (emi) produced by a system. setting bit 2 of register 0x18 will adjust the output driver circuitry to increase the rise and fall times of the signal. setting this bit will approximately double the nominal rise and fall times of the ds110df111 output driver. this bit is cleared by default. inverting the output polarity register 0x1f, bit 7 in some systems, the polarity of the data does not matter. in systems where it does matter, it is sometimes necessary, for the purposes of trace routing, for example, to invert the normal polarities of the data signals. the ds110df111 can invert the polarity of the data signals by means of a register write. writing a 1 to bit 7 of register 0x1f inverts the polarity of the output signal for the selected channel. this can provide additional flexibility in system design and board layout. overriding the figure of merit adaption register 0x2c, bits 5:4, register 0x31, bits 6:5, register 0x6b, register 0x6c, register 0x6d, and register 0x6e, bits 7 and 6 the default figure of merit for both the ctle and dfe adaptation is simple. the horizontal and vertical eye openings are measured for each ctle boost setting or set of dfe tap weights and polarities. the vertical eye opening is scaled to a constant reference vertical eye opening and the smaller of the horizontal or vertical eye opening is taken as the figure of merit for that set of equalizer settings. the objective is to adapt the equalizer to a point where the horizontal and vertical eye openings are both large and approximately equal in magnitude. this usually provides optimum bit error rate performance for most transmission channels. table 12. ds110df111 adaption algorithm settings, register 0x31 bits 6:5 adapt mode register 0x31, bit register 0x31, bit 5 setting adaption algorithm 6 adapt_mode [1] adapt_mode [0] < 1:0 > 0 0 00 no adaption 0 1 01 adapt ctle until optimum 1 0 10 adapt ctle until optimum the dfe, then ctle again (default) 1 1 11 adapt ctle until lock, the dfe, the ctle again in the ds110df111 the ctle figure of merit type is selected using the two-bit field in register 0x31, bits 6:5. table 13. figure of merit type settings value in bits 5:4 of figure of merit type register 0x2c 0x0 both heo and veo used 0x1 only heo used 0x2 only veo used 0x3 (default) both heo and veo used for some transmission media the adaptation can reach a better setting if a different figure of merit is used. the ds110df111 includes the capability of adapting based on a configurable figure of merit. the configurable figure of merit is structured as shown in the equation below. copyright ? 2013, texas instruments incorporated submit documentation feedback 27 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com fom = minimum [(heo - b) x a, (veo - c) x (1 - a)] where ? heo is horizontal eye opening ? veo is vertical eye opening ? fom is the figure of merit ? the factors a, b, and c are set using registers 0x6b, 0x6c, and 0x6d respectively (1) in order to use the configurable figure of merit, the enable bits must be set. to use the configurable figure of merit for the ctle adaptation, set bit 7 of register 0x6e. to use the configurable figure of merit for the dfe adaptation, set bit 6 of register 0x6e. the same scaling factors are used for both ctle and dfe adaptation when the configurable figure of merit is enabled. setting the rate and subrate for lock acquisition register 0x2f, bits 7:6 the rate and subrate settings, which constrain the data rate search can be set using channel register 0x2f. bits 7:6 are rate < 1:0 > , and bits 5:4 are subrate < 1:0 > . setting the adaption/lock mode register 0x31, bits 6:5, and register 0x33, bits 7:4 and 3:0, register 0x34, bits 3:0, register 0x35, bits 4:0, register 0x3e, bit 7, and register 0x6a there are four adaptation modes available in the ds110df111. ? mode 0: the user is responsible for setting the ctle and dfe (for the ds110df111) values. this mode is used if the transmission channel response is fixed. ? mode 1: only the ctle is adapted to equalize the transmission channel. the dfe is enabled , but the tap weights are all set to 0. this mode is primarily used for smoothly-varying high-loss transmission channels such as cables and simple pcb traces. ? mode 2: in this mode, both the ctle and the dfe are adapted to compensate for additional loss, reflections, and crosstalk in the input transmission channel. the maximum dfe tap weights can be constrained using register 0x34, bits 3:0, and register 0x35, bits 4:0. ? mode 3: in this mode, both the ctle and dfe are adapted as in mode 2. however, in mode 3, more emphasis is placed on the dfe setting. this mode may give better results for high crosstalk transmission channels. bits 6:5 of register 0x31 determine the adaptation mode to be used. the mapping of these register bits to the adaptation algorithm is shown in. by default the ds110df111 requires that the equalized internal eye exhibit horizontal and vertical eye openings greater than a pre-set minimum in order to declare a successful lock. the minimum values are set in register 0x6a. the ds110df111 continuously monitors the horizontal and vertical eye openings while it is in lock. if the eye opening falls below the threshold set in register 0x6a, the ds110df111 will declare a loss of lock. the continuous monitoring of the horizontal and vertical eye openings may be disabled by clearing bit 7 of register 0x3e. initiating adaption register 0x24, bit 2, and register 0x2f, bit 0 when the ds110df111 becomes unlocked, it will automatically try to acquire lock. if an adaptation mode is selected using bits 6:5 in register 0x31, the ds110df111 will also try to adapt its ctle and dfe. adaptation can also be initiated by the user. ctle adaptation can be initiated by setting and then clearing register 0x2f, bit 0. in the ds110df111, dfe adaptation can be initiated by setting and then clearing bit 2 of register 0x24. 28 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 overriding the ctle settings used for ctle adaption register 0x2c, bits 3:0, register 0x2f, bit 3, register 0x39, bits 4:0, and registers 0x40-0x4f the ctle adaptation algorithm operates by setting the ctle boost stage controls to a set of pre-determined boost settings, each of which provides progressively more high-frequency boost. at each stage in the adaptation process, the ds110df111 attempts to phase lock to the equalized signal. if the phase lock succeeds, the ds110df111 measures the horizontal and vertical eye openings using the internal eye monitor circuit. the ds110df111 computes a figure of merit for the eye opening and compares it to the previous best value of the figure of merit. while the figure of merit continues to improve, the ds110df111 continues to try additional values of the ctle boost setting until the figure of merit ceases to improve and begins to degrade. when the figure of merit starts to degrade, the ds110df111 still continues to try additional ctle settings for a pre-determined trial count called the ? look-beyond ? count, and if no improvement in the figure of merit results, it resets the ctle boost values to those that produced the best figure of merit. the resulting ctle boost values are then stored in register 0x03. the ? look-beyond ? count is configured by the value in register 0x2c, bits 3:0. the value is 0x2 by default. the set of boost values used as candidate values during ctle adaptation are stored as bit fields in registers 0x40-0x4f. the default values for these settings are shown in table 14 . these values may be overridden by setting the corresponding register values over the smbus. if these values are overridden, then the next time the ctle adaptation is performed the set of ctle boost values stored in these registers will be used for the adaptation. resetting the channel registers by setting bit 2 of channel register 0x00 will reset the ctle boost settings to their defaults. so will power-cycling the ds110df111. table 14. ctle settings for adaption, register 0x40-0x4f register bits 7:6 bits 5:4 bits 3:2 bits 1:0 ctle ctle adaptation (hex) (ctle stage 0) (ctle stage 1) (ctle stage 2) (ctle stage 3) boost index string 40 0 0 0 0 0000 0 41 1 0 0 0 1000 1 42 2 0 0 0 2000 2 43 1 1 0 0 1100 3 44 3 0 0 0 3000 4 45 2 1 0 0 2100 5 46 1 1 1 0 1110 6 47 2 2 0 0 2200 7 48 2 3 0 0 2300 8 49 2 1 1 1 2111 9 4a 1 2 2 1 1221 10 4b 3 1 1 1 3111 11 4c 2 1 2 1 2121 12 4d 2 2 1 1 2211 13 4e 3 2 1 2 3212 14 4f 3 3 2 1 3321 15 as an alternative to, or in conjunction with, writing the ctle boost setting registers 0x40 through 0x4f, it is possible to set the starting ctle boost setting index. to override the default setting, which is 0, set bit 3 of register 0x2f. when this bit is set, the starting index for adaptation comes from register 0x39, bits 4:0. this is the index into the ctle settings table in registers 0x40 through 0x4f. when this starting index is 0, which is the default, ctle adaptation starts at the first setting in the table, the one in register 0x40, and continues until the optimum fom is reached. copyright ? 2013, texas instruments incorporated submit documentation feedback 29 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 15. vod settings voda/b bit 2, sel_vod[2] bit 1, sel_vod[1] bit 0, sel_vod[0] output vod (mvppd) 0 0 0 0 600 r 0 0 1 700 0 1 0 800 0 1 1 900 f 1 0 0 1000 1 1 0 1 1100 1 1 0 1200 1 1 1 1300 setting the output differential voltage register 0x2d, bits 2:0 there are eight levels of output differential voltage available in the ds110df111, from 0.6 v to 1.3 v in 0.1 v increments. the values in bits 2:0 of register 0x2d set the output vod. the available vod settings and the corresponding values of this bit field are shown in table 15 . not all vod levels are available using the voda/b control pins. setting the output de-emphasis setting register 0x15, bits 2:0 and bit 6 fifteen output de-emphasis settings are available in the ds110df111, ranging from 0 db to -12 db. the de- emphasis values come from register 0x15, bits 2:0 and register 0x15, bit 6, which is the de-emphasis range bit. the available driver de-emphasis settings and the mapping to these bits are shown in table 16 . table 16. de-emphasis settings register 0x15 bit register 0x15 bit register 0x15 bit register 0x15 bit de-emphasis pin setting [2], drv_dem[2] [1], drv_dem[1] [0], drv_dem[0] [6], drv_dem_range settting (db) 0 0 0 0 0 0.0 0 0 1 1 -0.9 r 0 0 1 0 -1.5 0 1 0 1 -2.0 0 1 1 1 -2.8 1 0 0 1 -3.3 f 0 1 0 0 -3.5 1 0 1 1 -3.9 1 1 0 1 -4.5 0 1 1 0 -5.0 1 1 1 1 -5.6 1 1 0 0 0 -6.0 1 0 1 0 -7.5 1 1 0 0 -9.0 1 1 1 0 -12.0 30 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
ds110df111 www.ti.com snls461 ? may 2013 table 17. revision history revision date update comments 0.1 4-25-2012 lee sledjeski initial revision 0.2 7-23-2012 nate unger 1. added lbk pin and function2. 0.3 7-24-2012 nate unger 1.added pin mode functions; vod, de-emphasis, loopback, rate/subrate, 2.changed loopback feature to control wire-side loopback when pulled down 0.4 7-27-2012 nate unger 1. moved lbk pin to 6 2. removed rate and subrate 3. added dema and demb 4. added voda and vodb5 0.41 7-29-2012 nate unger revised look and feel to fit ti template added rate and subrate table for register operation added loopback diagrams fixed table and figure numbering fixed many formatting issues inserted register commands for loopback 0.42 8-1-2012 nate unger updated table reference numbers added register descriptions for 0x18, 0x1f, 0x20 reduced reference modes from table 21 fixed figure 1 reference on page fixed reference to vodb pin 10 in table 7 0.45 8-24-2012 lee sledjeski updated pin type to reflect definitions added shared reg0x07[1:0] for loopback added channel reg0x04[3:2] for dwdm/zr 0.5 9-27-2012 lee sledjeski updated address input to a 2-level pin updated table 9 (smbus address) added fanout modes to the loopback function reduced ctle table to 16 values 0.5 9-27-2012 lee sledjeski copied version from ds110rt/df111 0.51 9-28-2012 lee sledjeski updated rate/subrate information in table 13 0.52 9-28-2012 lee sledjeski updated graphics to ds125df111 part # 0.53 9-28-2012 lee sledjeski removed register description and tables added alpha vs production section 0.55 10-15-2012 lee sledjeski changed temperature range: -40 ? 85c 0.6 10-26-2012 lee sledjeski updated electrical table removed non-df information added addr1 input on pin 9 0.65 10-30-2012 lee sledjeski added los/int# pin 13 information updated graphics and tables to have a common pin naming convention; strap/slave/pin/master 11-7-2012 lee sledjeski converted to ds110 datasheet 0.70 12-12-12 lee sledjeski adjusted package thermal and power dissipation removed vrx-in increased dj to 5ps removed jtrans 0.71 12-18-12 lee sledjeski used ds110df111 version 0.70 as a starting point to create new ds125df111 datasheet updated default to be rate/subrate = 06 which enables all divider options 1,2,4, and 8. 0.8 1-31-2013 lee sledjeski removed references to alpha silicon made ds110 primary version default data ? rates 1.25 / 10.3125 gbps adjusted trise,tpd,tlock range added tpd ? raw data 0.81 2-04-2013 lee sledjeski updated 1st page graphic to remove tia interface 0.82 3-26-2013 lee sledjeski updated smbus table to match pinout 0.85 4-03-2013 lee sledjeski updated dem table to match prs features doc 0.9 4-10-2013 lee sledjeski updated version and device id (expected rtm) copyright ? 2013, texas instruments incorporated submit documentation feedback 31 product folder links: ds110df111
ds110df111 snls461 ? may 2013 www.ti.com table 17. revision history (continued) 0.91 4-10-2013 lee sledjeski fixed description on channel reg 0x31 0.92 4-16-2013 lee sledjeski updated vod table 17 32 submit documentation feedback copyright ? 2013, texas instruments incorporated product folder links: ds110df111
package option addendum www.ti.com 30-may-2013 addendum-page 1 packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) op temp (c) device marking (4/5) samples ds110df111sq/nopb active wqfn rtw 24 1000 green (rohs & no sb/br) cu sn level-3-260c-168 hr -40 to 85 1d111b3 ds110df111sqe/nopb active wqfn rtw 24 250 green (rohs & no sb/br) cu sn level-3-260c-168 hr -40 to 85 1d111b3 (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs), pb-free (rohs exempt), or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. pb-free (rohs exempt): this component has a rohs exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. the component is otherwise considered pb-free (rohs compatible) as defined above. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. (4) there may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) multiple device markings will be inside parentheses. only one device marking contained in parentheses and separated by a "~" will appear on a device. if a line is indented then it is a continuation of the previous line and the two combined represent the entire device marking for that device. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis.
tape and reel information *all dimensions are nominal device package type package drawing pins spq reel diameter (mm) reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p1 (mm) w (mm) pin1 quadrant ds110df111sq/nopb wqfn rtw 24 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 q1 ds110df111sqe/nopb wqfn rtw 24 250 178.0 12.4 4.3 4.3 1.3 8.0 12.0 q1 package materials information www.ti.com 23-jul-2013 pack materials-page 1
*all dimensions are nominal device package type package drawing pins spq length (mm) width (mm) height (mm) ds110df111sq/nopb wqfn rtw 24 1000 213.0 191.0 55.0 ds110df111sqe/nopb wqfn rtw 24 250 213.0 191.0 55.0 package materials information www.ti.com 23-jul-2013 pack materials-page 2
mechanical da t a r tw0024a www .ti.com s q a 2 4 a ( r e v b )
important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per jesd46, latest issue, and to discontinue any product or service per jesd48, latest issue. buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all semiconductor products (also referred to herein as ? components ? ) are sold subject to ti ? s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in ti ? s terms and conditions of sale of semiconductor products. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. ti assumes no liability for applications assistance or the design of buyers ? products. buyers are responsible for their products and applications using ti components. to minimize the risks associated with buyers ? products and applications, buyers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which ti components or services are used. information published by ti regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of significant portions of ti information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. ti is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ti components or services with statements different from or beyond the parameters stated by ti for that component or service voids all express and any implied warranties for the associated ti component or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of ti components in its applications, notwithstanding any applications-related information or support that may be provided by ti. buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. buyer will fully indemnify ti and its representatives against any damages arising out of the use of any ti components in safety-critical applications. in some cases, ti components may be promoted specifically to facilitate safety-related applications. with such components, ti ? s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. nonetheless, such components are subject to these terms. no ti components are authorized for use in fda class iii (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. only those ti components which ti has specifically designated as military grade or ? enhanced plastic ? are designed and intended for use in military/aerospace applications or environments. buyer acknowledges and agrees that any military or aerospace use of ti components which have not been so designated is solely at the buyer ' s risk, and that buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. ti has specifically designated certain components as meeting iso/ts16949 requirements, mainly for automotive use. in any case of use of non-designated products, ti will not be responsible for any failure to meet iso/ts16949. products applications audio www.ti.com/audio automotive and transportation www.ti.com/automotive amplifiers amplifier.ti.com communications and telecom www.ti.com/communications data converters dataconverter.ti.com computers and peripherals www.ti.com/computers dlp ? products www.dlp.com consumer electronics www.ti.com/consumer-apps dsp dsp.ti.com energy and lighting www.ti.com/energy clocks and timers www.ti.com/clocks industrial www.ti.com/industrial interface interface.ti.com medical www.ti.com/medical logic logic.ti.com security www.ti.com/security power mgmt power.ti.com space, avionics and defense www.ti.com/space-avionics-defense microcontrollers microcontroller.ti.com video and imaging www.ti.com/video rfid www.ti-rfid.com omap applications processors www.ti.com/omap ti e2e community e2e.ti.com wireless connectivity www.ti.com/wirelessconnectivity mailing address: texas instruments, post office box 655303, dallas, texas 75265 copyright ? 2013, texas instruments incorporated
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: texas instruments: ? ds110df111evm

▲Up To Search▲

Price & Availability of DS110DF111-14

	To Download DS110DF111-14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .